Technical specifications for IC660BBD025
Brand GE Fanuc
Series Genius I-O
Manufacturer GE Fanuc/Emerson Automation
Part number IC660BBD025
Series Genius I/O
Describes the Sink I/O block
Product Description 32 Circuit block I/O module
Compatible Series Series 90-30
Nooooo. Circuit number 32 I/O circuits
Voltage 5/12/24 V DC
Input signal voltage 5/12 24 / VDC TTL
.32
Input processing time is 1.4 ms
Load current 0.5 amp
Output current 0.5 amps per circuit
TTL (TTL) +5 volts
Maximum surge current 4 amps, maximum 10 ms
Block to block isolation 850 volts
Output Diagnose switch faults
Heat dissipation 11 watts (8 inputs), 18 Watts (32 inputs)
Compatible electronic component assembly IC660EBD025
Dimensions (H * W * D) 8.83×3.58×4.7 inches
Compatible terminal base assembly IC660TBD025

The IC660BBD025 is a Block I/O from the Genius I/O Block family. The device is primarily used to implement a distributed I/O architecture, as the IC660BBD025 is a fully functional Genius I/O node with thirty-two (32) I/O circuits, built-in Genius communication terminals, and an integrated handheld Monitor (HHM) port. The IC660BBD025 was previously manufactured by GE Fanuc Automation, but the product line and other automation equipment have been acquired by Emerson Automation. The module supports remote installation near the controlled machine or process, as the IC660BBD025 is able to communicate with controllers up to 7,500 feet away. It can be directly integrated with 90-30 series, 90-70 series controllers and other controllers that support communication protocols, as well as Genius bus controllers, interface modules and third-party devices. The module’s input circuit accepts the 10 to 30 VDC range of a 12/24 V nominal power supply; The voltage range from 4.9 to 5.3 VDC is only suitable for 5 V nominal power supplies in filling current configurations. The input circuit has an optional filtering time of 1, 2, 3, 4, 5, 10, 20, 30, 40, 50, 60, 70, 80, 90 or 100ms, and an input processing time of 1.4 ms. Each output circuit has a rated current of 0.5 amps and a maximum surge current of 4 amps for up to 10 milliseconds. The module has a total output current of 16 amps and a single output delay of 0.5 ms. Status LED indicators are provided with the IC660BBD025, such as Module OK and I/O Enabled. The module is also equipped with a resettable self-protection circuit and advanced diagnostic functions.

GE Fanuc Genius I-O IC660BBD025 I/O block is a receiver I/O block. It is rated for 5, 12 or 24 volts DC. It also comes with 32 I/O points. The block has a rated load current of 0.5 amps. I/O modules can be connected to different input devices, switches, and field devices. The IC660BBD025 I/O receiving module can be easily configured and can be used as an input or output device. The front of the block is equipped with different ports and LED indicators. There is a monitoring port at the top of the module that can be used to connect programmable controllers or monitoring devices. Below the monitoring ports, you can use serial ports 1 and 2 as well as Shield In and Shield Out ports. The GE Fanuc IC660BBD025 I/O Block comes with an I/ O-enabled LED and a unit normal LED that alerts the operator when the entire unit and I/O are in normal operating condition. Each of the 32 I/O points in front of the block has an LED that lights up when a particular I/O point is used. I/O blocks have been certified to UL standards and other industry standards. The IC660BBD025 I/O module has built-in protection, including overheat, overload and short circuit protection. This Genius I/O module is fully compatible with +5 volt transistor logic (TTL). The block is compact and measures 8.83 inches high, 3.58 inches wide and 4.7 inches deep. It emits 8 watts of heat with just 11 inputs, and 32 watts from all 18 points. Block to block isolation is 850 V.