Technical specifications for IC660BBA105
Brand GE Fanuc
Series Genius I/O
Manufacturer Emerson Automation/GE Fanuc (ever)
Part number IC660BBA105
Part number IC660BBA105
Describes an I/O block
Product description analog output module
Terminal 32
Nooooo. Output six (6) analog outputs
Output block 6
Each ordinary card counts a group of 6 people
Resolution 6μA
Output signal 4-20 MA
Operating voltage 93-132 V AC /105-145 V DC
Supply voltage range 115 V AC / 125 V DC
Output range 4-20 mah /0-24 mah

The IC660BBA105 is a Genius I/O Block component. The module is specifically an analog output module that operates at an input power supply voltage of 115 VAC or 125 VDC. The module is a panel mount device, secured through the provided mounting holes, secured using 8-32 screws, and grounded using star washers. It can be mounted on any housing, providing adequate air circulation and protection against industrial pollutants. The IC660BBA105 primarily has six (6) analog input channels that provide a 4-20 mA signal. Each channel has a configurable output Hold function, an important safety-related feature that allows the module to maintain the current output value in the event of a processor error or a change in mode of operation. In addition, the proportions of individual circuits can be set to engineering values to provide usable readings. It can also sense overrange and underrange conditions and output feedback errors. The output channel of the module can be put into operation without calibration. The IC660BBA105 has an output resolution of 6μA, an output update frequency of 25 ms, and an accuracy of 0.15% of a full-scale reading. It operates in an output range of 0-24 mA and a typical thermal drift of 35 PPM /°C. The recommended wire diameter for terminating the field signal line is AWG #14 (average cross section 2.1mm2) and the minimum recommended size is AWG #20 (average cross section.54mm2). For serial bus wiring, the recommended wire diametries are AWG #12 wire (average cross section 3.3mm2) and AWG #14 wire (average cross section 2.1mm2 each) for single wire connections. When two wires are required in a single terminal. The minimum recommended wire size for a serial bus is AWG #22 (average cross section.36mm2).

The IC660BBA105 module is a Genius I-O module compatible with GE Fanuc’s 90-30 series PLC systems. The module has 32 terminals and 6 output blocks. The module has a resolution of 6 microamps. It comes with 6 points and the modules operate at 93 to 132 volts AC and 105 to 145 volts DC. I/O modules have an output range of 4 to 20 mah or 0 to 24 mah. This Genius I-O analog device has an open housing that should protect against water splashes and air pollutants. The IC660BBA105 module is 8.83 inches high, 3.50 inches wide and 3.94 inches deep. The front of the module is equipped with a unit normal LED and an I/O enabled LED. The IC660BBA105 module has a block-to-block isolation of 1500 volts with a duration of 1 minute. For regular operation, the I/O module generates 12 watts of heat as energy dissipation. The ambient temperature of the module should not exceed 60 degrees Celsius. The IC660BBA105 module is connected to the handheld programming unit using a monitoring port. The I/O module operates at 50 to 60 Hz. It comes with Serial 1, Serial 2, Shield In, and Shield Out connectivity ports. An I/O block has separate circuits that are electrically common but isolated from other circuits. The IC660BBA105 module has one of the enhanced diagnostic functions in the I/O module, making it easy to detect no-load errors, overload errors, short-circuit errors and other errors. The module has baud rates of 76.8 and 38.4 kbaud.